150w Street Light Housing Wholesaler Introduces Energy-saving Requirements For Road Lighting
2021年6月9日150w Street Light Housing Wholesaler introduces energy-saving techniques for road lighting:
1. Efficient light source
At present, the luminous efficiency of LED is only 50lm/W, which is much lower than sodium lamp 120lm/W. Sodium lamp tube can withstand high temperature of 800 degrees and work normally, while at the same luminous flux, the heat is more serious LED, semiconductor material limit temperature is only 150 degrees, package The resin temperature is lower, the resin ages very seriously at high temperatures, and the LED is affected by the characteristics of the excited material, and the light half-life is short. These are problems that cannot be solved at present. At present, LED has become the mainstream lighting source, and there is no theoretical support.
2. High-efficiency reflective lamps
The use of new materials and optimizing the angle of reflection can appropriately improve the light efficiency and change the sanding habits of traditional landscape lamp balls. The use of directional coating internal luminescence technology can greatly improve the ground illumination of traditional landscape lamps. Timely cleaning of lamps is also one of the means of energy saving.
3. Control energy saving "according to time period scenario"
For urban road lighting, the most effective and concise method is to use multi-period "scene" energy-saving control to save energy. The lighting of cities, highways and tunnels is different from commercial lighting or household lighting. For occasions where precision assembly is required in the workshop, the lighting must meet the specified value, otherwise, the energy-saving illumination will be low, the defective products will be more, the unit qualified products will use more energy, the wages and other expenses will be more cost-sharing, and the gain will not be worth the loss. In these fixed lighting occasions, methods such as replacing the light source of lamps and lanterns are generally used to meet the requirements of illuminance and energy saving, and people can turn off the lights. For urban lighting, it is difficult to meet the needs of road lighting scenarios in the middle of the night and later in the middle of the night by using fixed voltage reduction or changing the light source of the lamp and changing the low power.
Through the above introduction, Die-Cast Housing Factory hopes that you can simply refer to the content of this article in future use.
1. Efficient light source
At present, the luminous efficiency of LED is only 50lm/W, which is much lower than sodium lamp 120lm/W. Sodium lamp tube can withstand high temperature of 800 degrees and work normally, while at the same luminous flux, the heat is more serious LED, semiconductor material limit temperature is only 150 degrees, package The resin temperature is lower, the resin ages very seriously at high temperatures, and the LED is affected by the characteristics of the excited material, and the light half-life is short. These are problems that cannot be solved at present. At present, LED has become the mainstream lighting source, and there is no theoretical support.
2. High-efficiency reflective lamps
The use of new materials and optimizing the angle of reflection can appropriately improve the light efficiency and change the sanding habits of traditional landscape lamp balls. The use of directional coating internal luminescence technology can greatly improve the ground illumination of traditional landscape lamps. Timely cleaning of lamps is also one of the means of energy saving.
3. Control energy saving "according to time period scenario"
For urban road lighting, the most effective and concise method is to use multi-period "scene" energy-saving control to save energy. The lighting of cities, highways and tunnels is different from commercial lighting or household lighting. For occasions where precision assembly is required in the workshop, the lighting must meet the specified value, otherwise, the energy-saving illumination will be low, the defective products will be more, the unit qualified products will use more energy, the wages and other expenses will be more cost-sharing, and the gain will not be worth the loss. In these fixed lighting occasions, methods such as replacing the light source of lamps and lanterns are generally used to meet the requirements of illuminance and energy saving, and people can turn off the lights. For urban lighting, it is difficult to meet the needs of road lighting scenarios in the middle of the night and later in the middle of the night by using fixed voltage reduction or changing the light source of the lamp and changing the low power.
Through the above introduction, Die-Cast Housing Factory hopes that you can simply refer to the content of this article in future use.
コメント